dbx 215s Dual Channel 15-Band Equalizer

dbx 215s Dual Channel 15-Band Equalizer XLR and TRS IN/OUT

dbx Professional Products by Harmen
EXCEPTIONAL SOUND and RUGGED RELIABILITY

Rack Mountable with Active-balanced 3-pin XLR-type and TRS 1/4-inch inputs

When the pros need an EQ, they turn to dbx. With a proven track record that spans four decades, dbx® EQs are the industry standard for touring, studios, and audio installations. With the dbx heritage of revered pro EQs, the 215s meets the needs of the most demanding sound reinforcement environments, while offering the simplicity of straightforward controls.

The dbx 215s includes two 15-band channels of 2/3-octave equalization, ±12 dB input gain, switchable ±6 dB or ±12 dB boost/cut range, 20mm nonconductive sliders, an intuitive user interface, and output level metering. From its extended 10Hz to 50kHz frequency response and 112 dB dynamic range to the quality componentry and meticulous attention to detail, the 215s offers exceptional sound and rugged reliability that guarantees you will always sound your best.

Sure to find a home in the studio, on tour and with installed sound venues, the dbx 215s is destined to take its rightful place in the lineage of great dbx signal processors that are the professional's choice in signal processing. With such affordable quality, there's no longer any excuse for compromising your sound.

Features:
  • Dual 15-band, 1/3-octave Constant Q frequency bands
  • 4-segment LED ladders for monitoring output levels
  • Front panel bypass switch
  • XLR and TRS Inputs and Outputs
  • Switchable boost/cut ranges of ±6 or ±12 dB
  • ±12 dB input gain range
  • Dynamic range of greater than 108dB
  • Frequency Response of <10hz to="">50kHz
Specifications:
  • Input Connectors 1/4" TRS, female XLR (pin 2 hot)
  • Input Type Electronically balanced/unbalanced, RF filtered
  • Input Impedance Balanced 40 kOhm, unbalanced 20 kOhm
  • Max Input >+21dBu balanced or unbalanced
  • CMRR >40dB, typically >55dB at 1kHz
  • Output Connectors 1/4" TRS, male XLR (pin 2 hot)
  • Output Type Impedance-balanced/unbalanced, RF filtered
  • Output Impedance Balanced 100 ohm, unbalanced 50 ohm
  • Max Output >+21dBu balanced/unbalanced into 2 kOhm or greater; >+18dBm balanced/unbalanced (into 600 ohm)
  • Bandwidth 20Hz to 20kHz, +0.5/-1dB
  • Frequency Response <10hz to="">50kHz, +0.5/-3dB
  • Dynamic Range Typically >112dB
  • Signal to Noise Ratio Typically >95dB
  • THD+Noise <0.003%>
  • Interchannel Crosstalk <-90db, 20hz="" to="" 20khz="">
  • Bypass Switch Bypasses the graphic equalizer section in the signal path
  • Low cut Switch Activates the 50Hz 12dB/octave Bessel high-pass filter
  • Range Switch Selects either +/- 6dB or +/- 12dB slider boost/cut range
  • Operating Voltage 100VAC-240VAC 50/60Hz
  • Power Consumption 15W
  • Power Connector IEC receptacle
  • Unit Weight 4.8 lbs.(2.2 kg)
  • Shipping Weight 6.2 lbs.(2.8kg)
  • Dimensions 1.75" (4.4cm) H x 6"(15.24cm) D x 19" (48.26cm) W

Clean church pull, "only driven once a week by a little old lady :) "

CHECK ALL SHIPPING OPTIONS FOR LOWEST COST OR BEST OPTION
Grab this GREAT ITEM now before someone else does

Please refer to all photos as they are part of the description and stated condition.
Sale is for described item only. Props seen in photos are not included. If uncertain, please ask before ordering.

dbx
335430481341
1 Item
Used
Pulled from a working environment (a local Church), power tested, and powers on as it should. No further testing has been performed on this device. It requires a standard three prong power cord, which will be included.

Data sheet

Input/Output Ports
TRS 1/4" In
TRS 1/4" Out
XLR In
XLR Out
Rack Unit Height
1U

You might also like

2 other products in the same category: